|
In-Rail-Mini-Modbus DZU 1452
/ DZU 1462 |
DZU1461
/ DZU1462 인레일미니 초슬림형 모드버스
RS485 RTU 모듈용 전원공급 단말기 In-Rail-Mini Modbus
Power Terminal
DZU 1461 / DZU 1461
인레일버스(In-Rail-Bus)의
확장
최대
7개의 모드버스
RTU (RS485) 모듈을 연결할 수 있는 새로운 인레일미니(In-Rail-Mini)는
저비용, 소형 시스템 구축에 용이합니다.
인레일미니
모드버스에서는 신호에 종단저항(Termination
resistor) 및
분극저항(Polarization resistor)을 연결할 수 있습니다.
Extension
of the In-Rail-Bus:
The
new In-Rail-Mini for up to 7 devices facilitate
the construction of a low-cost and small
system.
The
In-Rail-Mini Modbus allows the connection
of termination and polarization resistors.
|
소형 인레일버스 설치를
위한 경제적인 비용의 효율적이고 빠른 솔루션
In-Rail-Mini Modbus는 In-Rail-Bus 커넥터에 전압 24V DC의
전원을 공급하고 Modbus 라인 A와 B를 연결하는데 사용됩니다. 라인 E는 그룹 메시지에 사용할 수 있습니다. (예: 그룹 오류 메시지). DIP 스위치는 RS485 인터페이스용 종단
저항(Terminating
Resistors) 및 분극 저항(Polarization Resistors)를 연결하는데 사용할 수 있습니다.
인레일미니는 7.5mm 및 15mm의 DIN 레일 깊이에 사용 가능합니다 (주문 정보 참조).
for installation of small Modbus applications with In-Rail Bus System
Cost-effective and fast solution for small In-Rail-Bus installations. The In-Rail-Mini Modbus is used to put the supply voltage 24 V DC into the In-Rail-Bus connectors and to connect the Modbus lines A and B. Line E is available for group messages, e.g. for a group error message. DIP switches can be used to connect the usual terminating and polarization resistors for RS 485 interfaces. The In-Rail-Minis are available for DIN rail heights of 7.5 mm and 15 mm (see order information). | In-Rail-Mini Modbus | Supply voltage | 24 V DC (working range 16.8 V … 32 V DC) | Input current | ≤ 1 A (Fuse recommendation 1.25 AT) | Modules amount | Max. 7 DRAGO Modbus Modules DMB series | Network Modbus | Terminating and polarisation resistors can be switched on via DIP switch | Group message E | Group message, Pull-up resistor can be switched on via DIP switch | Connection (captive clamp screws) | 0.08 ... 1.5 mm² / AWG 28 ... 18 with ferrule Stripped length: 7 mm / 0.3 in Screw terminal torque: 0.22 ... 0.25 Nm / 0.15 ... 2.2 lbf in | Dimensions | DZU 1461: 35 x 7.5 mm DIN rail DZU 1462: 35 x 15 mm DIN rail Full length 70 mm, available module space 50 mm |
Terminal assignments Terminal | 1 | 2 | 3 | 4 | 5 | 6 |
---|
Conductor strip | A | B | C | E | C | D | Signal | Modbus A | Modbus B | GND | Group Message | GND | +24 V |
모듈의 설치 위치에
주의하십시오! 모듈을 거꾸로 설치하지 마십시오.
Observe the installation position of the modules!
Do not snap the modules upside down. DIP Switch S1- | 1 | 2 | 3 | 4 |
---|
Function | 120 Ohm Termination | Pull-Up A Polarization | Pull-Down B Polarization | Group Message 4k7 Pull-Up |
사용설명서
(User Instructions) 다운로드
제품
주문 코드 Order Codes
품목
|
|
주문번호 |
In-Rail-Mini Modbus for DIN rail
|
Din
Rail
|
35
x 7.5mm
|
35 x 15mm
|
모드버스
모듈용 (Modbus)
|
DZU
1461
|
DZU
1462
|
여기에
표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications
listed here are subject to change without notice!)
|