|
Resistance Transmitter DR 41
- Cost optimized resistance measuring
in 2-, 3- and 4-wire sensor connection - Only 60 mm installation depth, 11.2 mm wide
Can be installed in economical standard terminal boxes - Fixed ranges, easy to use
Ready to use without any settings or adjustments - Zero/Span compensation on front panel
for readjustment of sensor and measuring equipment or line compensation at 2-wire sensor connection - True 3-port separation
Protection against erroneous measurements due to parasitic voltages or ground loops - Protective Separation acc. to EN 61140
Protects service personnel and downstream devices against impermissibly high voltage - Unlimited use with 24 V AC/DC power supply
Universally applicable for all measurement and industrial applications - 5 Years Warranty
Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)
|
|
DR41
경제형 저항 신호전송기 (트랜스미터) Resistance Transmitter DR 41
고정된 범위
설정으로 2선식 / 3선식 / 4선식 저항 신호
측정
저항 트랜스미터 DR41은 센서 저항 값을 표준 신호로 변환하고 출력에서 갈바닉 절연되어 있습니다.
The Resistance Transmitter DR 41 converts the sensor resistance value to a standard signal and makes it galvanic isolated available on output.
입력 |
20Ω
50Ω
100Ω
200Ω
500Ω
1000Ω
2000Ω
5000Ω
|
10kΩ
20kΩ
50kΩ
100kΩ
200kΩ
500kΩ
1MΩ
|
출력 | 0 ~ 20mA
4 ~ 20mA 0 ~ 10V
2 ~ 10V
0 ~ 5V 1 ~ 5V |
전원 | 24V AC/DC |
특징 |
다양한
범위의 저항 형식 신호(2 / 3 /
4선식) 입력 옵션 저비용, 슬림/초소형 (60 x 60 x 11.2mm)
|
- 비용 최적화된 저항 측정
2, 3 및 4선식 센서 연결
- 단지 60mm 설치 깊이, 폭 11.2mm
경제적인 표준 단자함에 설치할 수 있습니다.
- 사용하기 쉬운
고정 범위
설정이나 조정
없이 바로 사용할 수 있습니다.
- 전면 패널의 Zero/Span 보상
2선식 센서 연결시 센서 및 측정 장비 또는 라인 보정 재조정용
- 완전한 3-port 분리
부유전압(Stray
Voltage) 또는 접지루프(Ground
Loop)로 인한 잘못된 측정으로부터 보호
- EN
61140 (KS
C IEC 61140) 규격에 따른 감전보호
허용되지 않는 고전압으로부터 서비스 요원 및 후속 장치를 보호합니다.
- 24V AC/DC 전원 공급 장치로 무제한 사용 가능
모든 측정 및 산업용 활용에 보편적으로 적용 가능
- 5년 보증
배송일로부터 5년 이내에 발생하는 결함은 무료로 수리
또는 교환해 드립니다.
|
저항
신호전송기(Resistance Transmitter) DR41은 센서 저항값을
표준신호로 변환하고 출력에서 갈바닉 절연(Galvanic Isolated)
상태로 만듭니다.
하나의
측정범위만 사용하는 어플리케이션의 경우, 저항 신호전송기
DR41은 비용 효율적인 대안을 제공합니다.
보조전원
공급 장치용 교차 연결기(Cross-Connector)는 빠르고 쉬운
설치를 보장합니다. 11.2mm 너비의 슬림형 하우징은 DIN
레일에 상당한 공간을 절약합니다. 필요한 경우 전면 커버
뒤의 제로/스팬 전위차계(Zero/Span Potentiometer)에서
측정범위 보정을 수행할 수 있습니다.
아날로그
신호처리는 응답시간이 짧고 출력에서 뛰어난 신호재생으로
정확한 측정값을 보장합니다. 방호분리(Protective Separation)
및 24V AC/DC 전원공급 장치는 DR41을 모든 계측, 산업용
어플리케이션 및 빌딩 자동화에 보편적으로 적용할 수 있도록
합니다.
The Resistance Transmitter DR 41 converts the sensor resistance value to a standard signal and makes it galvanic isolated available on output.
For applications where one measuring range only is used, the Resistance Transmitters DR 41 offers a cost-effective alternative. A cross-connector for the auxiliary power supply ensures fast and easy installation. The slim housing with 11.2 mm width saves significant space on the DIN-rail. If required a measuring range compensation can be performed at the Zero/Span potentiometers behind the front cover. Analog signal processing guarantees precise measured values with short response times and outstanding signal reproduction at the output. Protective Separation and the 24 V AC/DC power supply make the DR 41 universally applicable for all measurement and industrial applications, as well as for building automation.
Technical Data
Input
Measuring range | Fixed ranges within 20 Ohm to 1 MOhm, see product line | Sensor connection | 2-wire, 3-wire, 4-wire sensor connection, see product line | Sensor wire resistance | < 25 Ohm / wire, maximum 5 % of final value at 2-wire connection | Sensor current | 0.1 μA to 5 mA, depends on measuring range |
Output
Output signal | 0 to 20 mA, 0 to 5 V, 0 to 10 V, see product line 4 to 20 mA, 1 to 5 V, 2 to 10 V | Load | Current output Voltage output | ≤ 500 Ohm ≥ 2 kOhm | Residual ripple | < 10 mVrma |
General Data
Transmission error | < 0.2 % full scale | Temperature coefficient 1) | < 0.025 %/K | Zero/Span compensation | ± 5 % | Response time T99 | < 2 ms | Test voltage | 3 kV AC, 50 Hz, 1 min., input against output against power supply | Working voltage 2) (Basic Insulation) | 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 | Protection against electrical shock 2) | Protective separation according to EN 61140 by reinforced insulation in accordance with EN61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits. | Ambient temperature | Operation Transport and storage | –20 °C to +60 °C (–4 °F to +140 °F) –35 °C to +85 °C (–31 °F to +185 °F) | Power supply | 24 V AC/DC, ± 15 % | AC: 48 to 62 Hz, approx. 2 VA DC: approx. 0.7 W | EMC 3) | EN 61326 -1 | Construction | 11.2 mm (0.44") housing, protection class: IP 20 mounting on 35 mm DIN rail acc. to EN 60715 | Weight | Approx. 50 g |
Block
Diagram
|
Dimensions
|
|
|
Terminal assignments
/ Wire cross-section max. 2.5 mm²
1 | Input R |
5 | Output + |
2 | Input R |
6 | Output - |
3 | Input 3-wire |
7 | Power supply ~ |
4 | Input 4-wire |
8 | Power supply ~ |
제품
주문 코드 Order Codes
품목 |
주문번호 | 저항 신호전송기
(트랜스미터) 고정 저항범위 및 출력
Resistance Transmitter | 모델
코드
| 측정저항
범위 코드
| 출력
신호 코드
|
2선식
DR 41 P -2 | | X | |
X |
3선식
DR 41 P -3 | | X | |
X |
4선식
DR 41 P -4 | | X | |
X | | 0 to 20Ω | 2 | 0 to 20 mA |
2 |
| 0 to 50Ω | 3 | 4 to 20 mA |
4 |
| 0 to 100Ω | 4 | 0 to 5 V |
5 |
| 0 to 200Ω | 5 | 1 to 5 V |
8 | | 0 to 500Ω | 6 | 0 to 10 V |
6 |
| 0 to 1000Ω | 7 | 2 to 10 V |
7 |
| 0 to 2000Ω | 8 |
|
|
| 0 to 5000Ω | 9 |
|
| | 0 to 10kΩ | A | |
|
| 0 to 20kΩ | B |
|
|
| 0 to 50kΩ | C |
|
| | 0 to 100kΩ | D | |
|
| 0 to 200kΩ | E |
|
| | 0 to 500kΩ | F | |
|
| 0 to 1MΩ | G |
|
|
측정저항
범위: 2선식 0 ~ 100Ω, 출력: 4 ~ 20mA
인 경우 주문번호 예시 |
DR 41 P -244 | 최대 10개의 경제형(Tiny
Snap) 신호변환기의 공급전원을
서로 연결할 수 있는 전원연결
단자 Cross-Connector:
2개1세트,
분할 가능 | DZU 0801 |
여기에
표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications
listed here are subject to change without notice!)
|