드라고 신호변환기      DRAGO Signal Converters

측정, 제어, 자동화를 위한 산업용 신호처리, DRAGO가 합니다.

페이지

Homepage

제품군

Product Line

제품소개

Products

신호변환기 선정 가이드

Selection Matrix

제품 전체 보기

Service Web Portals

내려받기

Downloads

제품 및 구입 문의

Contact

DG3202

Limit Value Monitor DG 3202

 

  • Easy configuration on front panel
    Operating mode switchable via DIP switch, switch point and hysteresis adjustable with potentiometer
  • Status indication by LED
    Easy monitoring and switching point adjustment
  • Relay changeover contacts with high power handling
    or fully isolated transistor switching outputs
  • True 4-port separation
    Protection against erroneous measurements due to parasitic voltages or ground loops
  • Protective Separation acc. to EN 61010
    Protects service personnel and downstream devices against impermissibly high voltage
  • High reliability and noise immunity
    No microprocessor, no integrated software
  • Extremely slim design
    12.5 mm slim housing for a simple and space saving DIN rail mounting
  • 5 Years Warranty
    Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant

DG3202 / DG3282 신호 한계 감시 알람 릴레이
Limit Value Monitor DG 3202 / DG 3282

2개의 스위칭 출력으로 표준 신호 모니터링

한계값 모니터 DG3202 및 DG3282는 0(4) ~ 20mA 및 0 ~ 10V 표준 신호 회로의 측정값을 모니터링하는데 사용됩니다. 2선식 트랜스미터의 작동을 위하여 트랜스미터용 전원공급 회로 +Us가 제공됩니다.

The Limit Value Monitors DG 3202 und DG 3282 are used to monitor measured values in 0(4) ... 20 mA and 0 ... 10 V standard signal circuits. A transmitter supply +Us is provided for the operation of 2-wire transmitters.

입력

0 ~ 20mA     4 ~ 20mA     0 ~ 10V

2선식 트랜스미터 전원 공급 및 신호 입력 (0~20mA / 4~20mA)

릴레이 출력
(DG32
02)

AC  250V / 6A     1500VA

DC  250V / 0.2A     115V / 0.3A     30V / 6A

오픈컬렉터 출력
(DG32
82)

30V DC / 50mA

전원

24V DC

특징

표준 신호 한계값 모니터링 및 알람 출력
SPDT 2개 출력, 6A 고용량 릴레이
두께 12.5mm 슬림형,
높은 내전압 4kV, 5년 보증

  • 전면 패널에서 간편한 설정
    DIP 스위치를 통해 작동 모드 전환 가능, 스위치 포인트 및 전위차계로 조정 가능한 히스테리시스
  • LED를 통한 상태 표시
    간편한 모니터링 및 스위칭 포인트 조정
  • 고전력 처리 기능을 갖춘 릴레이 전환 접점
    또는 완전히 절연된 트랜지스터 스위칭 출력
  • 진정한 4포트 분리
    기생 전압 또는 접지 루프로 인한 측정 오류로부터 보호
  • 보호 분리 (EN 61010)
    허용되지 않는 고전압으로부터 서비스 인력과 예하 장치를 보호
  • 높은 신뢰성과 노이즈 내성
    마이크로프로세서나 소프트웨어를 사용하지 않음
  • 매우 슬림한 디자인
    간단하고 공간 절약형 DIN 레일 설치를 위한 12.5mm 슬림형 하우징
  • 5년 보증
    납품일로부터 5년 이내에 발생한 하자는 무상으로 수리해 드립니다.

2개의 스위칭 출력은 개방회로(N/O) 또는 폐쇄회로(N/C) 작동에서 MIN 또는 MAX 알람으로 아날로그 제어 소자를 사용하여 두 출력을 동시에 또는 독립적으로 설정할 수 있습니다.

모든 설정 요소는 전면 커버 뒤에 있으며, 기기가 설치된 경우에도 설정 작업을 수행할 수 있습니다. 스위칭 지점과 스위칭 히스테리시스는 전위차계를 사용하여 조정할 수 있습니다. 모니터링 상태는 노란색 LED로 표시됩니다.

DG3202에서는 2개의 릴레이 전환 접점을 사용할 수 있습니다. DG3282에는 풀업 저항과 함께 선택적으로 작동할 수 있는 2개의 절연 트랜지스터 스위칭 접점(오픈컬렉터)이 출력됩니다. 신호입력, 전원공급,  신호출력 회로는 서로 안전하게 갈바닉 절연되어 있습니다.

보호분리 및 24V DC 공급전원으로 DG3202 및 DG3282는 모든 측정 및 산업 응용분야는 물론, 빌딩 자동화에도 보편적으로 적용할 수 있습니다.

Two switching outputs can be configured simultaneously or independently of each other with the analog control electronics as MIN or MAX alarm in open-circuit or closed-circuit operation.

All setting elements are located behind the openable front cover and can also be operated when the unit is mounted. The switching points and the switching hysteresis can be adjusted with potentiometers. The monitoring states are indicated by yellow LEDs.

Two relay changeover contacts are available on the DG 3202. The DG 3282 is equipped with two isolated transistor switching contacts (open-collector), which can optionally work with pull-up resistors. Input, power supply and the outputs are safely galvanically isolated from each other.

The Protective Separation and the 24 V DC power supply make the DG 3202 and DG 3282 universally applicable for all measurement and industrial applications, as well as for building automation.

 

Technical Data

Input

Input Signal Ranges

0(4) ~ 20 mA

 0 ~ 10 V

Input resistanceCurrent Input approx. 5 ΩVoltage Input approx. 120 kΩ

Overload max.

Current Input 200 mAVoltage Input 300 V

Transmitter supply +Us

16 V at UPower = 24 V, (13 V ~ 22 V depending on the supply voltage)
current limited ≤ 30 mA

Switch point setting

0 to 110 % with 12-turn potentiometer, independently adjustable for each switching output

 Hysteresis setting

0 to 6 % or 0 to 60 % of measuring range switchable, adjustable with potentiometer

 

Output

DG3202
(Relay)

Contact type2 changeover relays (SPDT)
Switching capability AC max.250 V / 6 A     1500 VA
Switching capability DC max.250 V / 0.2 A   115 V / 0.3 A   30 V / 6 A

 

Recommended minimum load 300 mW / 5 V / 5 mA

DG3282
(Transistor)

Contact type2 transistor switches, fully isolated, optional 10 kΩ Pull-up resistor
Switching capability30 V DC, max. 50 mA, residual voltage < 1.5 V, not current limited

Status indication

one yellow LED per switching output

Response time

approx. 20 ms

 

General Data

Switch error

< 0.2 % full scale
Temperature coefficient 1)< 150 ppm/K
Test voltage

4 kV AC, 50 Hz, 1 min. input against power supply against both switching outputs
3 kV AC, 50 Hz, 1 min. switching output 1 against switching output 2

Working voltage (Basic Insulation)2)

1000 V AC/DC for overvoltage category II and 600 V AC/DC for overvoltage category III according to DIN EN 61010 with pollution degree 2 between input, power supply and both switching outputs. Furthermore 300 V AC/DC between output 1 and output 2.

Protection against electrical shock 2)

Protective separation according to DIN EN 61140 by reinforced insulation according to DIN EN 61010 up to 600 V AC/DC at overvoltage category II and 300 V AC/DC at overvoltage category III at pollution degree 2 between input, power supply and both switching outputs. Furthermore 300 V AC/DC between output 1 and output 2.

Power supply

24 V DC, ± 15 %, approx. 1.0 W

Ambient temperatureOperation
Transport and storage
–20 °C to +60 °C    (-4 to +140 °F)
–35 °C to +85 °C    (-31 to +185 °F)
EMC 3)EN 61326-1

MTBF (EN 61709 / SN 29500)

575.4 years (Tamb.40 °C, FIT 198)

Construction

12.5 mm (0.5") housing, protection class IP 20
mounting on 35 mm DIN rail (EN 60715)

Weight70 g
  1. Average TC related to full scale value in specified operating temperature range, reference temperature 23 °C
  2. For applications with high working voltages, ensure there is sufficient spacing or isolation from neighboring devices and protection against electric shocks.
  3. Minor deviations possible during interference

 

Block Diagram

Dimensions

DG3202

DG3202

Terminal assignments

1.1

Power supply +

2.1

 Input Voltage +

1.2

Power supply -

2.2

Transmitter Power Supply +Us

 

 

3.1

Input Current +

 

 

3.2

Input -

 

OUTPUT 1

OUTPUT 2

 

DG3202 Relay

DG3282 Transistor

 

DG3202 Relay

DG3282 Transistor

4.1

COM

Out+

6.1

COM

Out+

4.2

NO

Out-

6.2

NO

Out-

5.1

NC

Pull-Up

5.2

NC

Pull-Up

 

 

제품 주문 코드   Order Codes

품목

주문번호

신호 한계 감시 알람: 릴레이 출력
Limit Value Monitor, Relay Output

DG 3202

신호 한계 감시 알람: 오픈컬렉터 출력
Limit Value Monitor, Transistor Output

DG 3282

 

여기에 표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications listed here are subject to change without notice!)
© Copyright 2004-2024 by DRAGO Automation GmbH

드라고 신호변환기 한국판매원 - 에이콤 (AKORM Corp.)